#Port For Remote Access Install The PEFNG

Since the Internet is involved, data traffic between the controllerand the remote AP is VPN encapsulated. Go to Security > Remote Management, and you can manage your router from a remote device via the internet.The Secure Remote Access Point Service allows AP users, at remote locations, to connect to an Arubacontrollerover the Internet. Note: If your PC is blocked but you want to access the router again, press and hold the Reset button to reset the router to the factory defaults. 3) Click Add, and your PCвЂ™s MAC address will also be listed.

In order to check ports on a Mac, follow the plan below: Open 'Network Utility' > Click 'Port Scan' > Indicate the hostname and ports to scan the remote host e.g. This way.An alternative to telnet in checking ports is Network Utility. This chapter discusses the following topics:To let the NAS on your local area network allow access from devices on the internet, you must first set up the correct port forwarding on your router.

Select the Remote Login checkbox. I also set up a dyndns host to deal with the changing IP On your Mac, choose Apple menu > System Preferences, click Sharing, then select Remote Login. I configure PuTTY to go through the proxy, and to tunnel port 5900.

AP control and 802.11 data traffic are carried through this tunnel. VNC server configuration.вЂњDeploying a Branch Office/Home Office SolutionвЂќRemote APs connect to a controllerusing Extended Authentication and Internet Protocol Security (XAuth/IPSec). If you need to enable access to additional server users, you must open ports above 5903 by manually specifying the port numbers. Only these users: Click the Add button. Specify which users can log in: All users: Any of your computerвЂ™s users and anyone on your network can log in.

In this case, both the AP and controllerare in the companyвЂ™s private address space.The remote AP must be configured with the IPSec VPN tunnel termination point. For example, voice over IP (VoIP) applications can be extended to remote sites while the servers and the PBX remain secure in the corporate office.Secure Remote Access Point Service can also be used to secure control traffic between an AP and the controllerin a corporate environment. Remote users can use the same features as corporate office users.

The following procedure describes how to create a DMZ address on the controller.1. This can be either a routable IP address that you configure on the controller, or the address of an external router or firewall that forwards traffic to the controller. For information on remote AP modes of operation, refer to вЂњAdvanced Configuration OptionsвЂќConfigure a Public IP Address for the ControllerThe remote AP requires an IP address to which it can connect in order to establish a VPN tunnel to the controller. The information in this section assumes the default mode of operation. This mode enables the virtual AP when the remote AP connects to the controller.

On the NAT device, you must enable NAT-T (UDP port 4500 only) and forward all packets to the public address of the NAT device on UDP port 4500 to the controllerto ensure that the remote AP boots successfully.This section describes how to configure the IPSec VPN server on the controller. When both the controllerand the AP are behind NAT devices, configure the AP to use the NAT deviceвЂ™s public address as its master address. Enter the IP Address and Net Mask fields.Communication between the AP and secure controlleruses the UDP 4500 port. Click Edit for the VLAN you just created.8. Navigate to the Configuration >Network > IP page.7. Select the port that belongs to this VLAN.6.

Configure the L2TP pool from which the APs will be assigned addresses, then click Done.The size of the pool should correspond to the maximum number of APs that the controller is licensed to manage.5. To configure the L2TP IP pool, click Add in the Address Poolssection. Make sure that only PAP (Password Authentication Protocol) is selected for Authentication Protocols.4. Navigate to the Configuration >Advanced Services >VPN Services > IPSec page.3. The remote AP will be a VPN client that connects to the VPN server on the controller.1.

Port For Remote Access Install The PEFNG

Navigate to the Configuration >Security >Access Control > Policies page.3. You must install the PEFNG license, as described in Chapter 31, вЂњSoftware LicensesвЂќ.To configure the user role, you create a policy that permits the following traffic:AP control traffic via the Aruba PAPI protocolLayer-2 Tunneling Protocol (L2TP) trafficTFTP traffic from the remote AP to the controllerFTP traffic from the remote AP to the controllerThen, you create a user role that contains this policy.1. The appropriate ACLs need to be enabled to permit traffic from the controllerto the AP and back to facilitate the bootstrap process.User roles and policies require the PEFNG license. This role is a temporary role assigned to the AP until it completes the bootstrap process after which it inherits the ap-role. Click Done to return to the IPSec page.Once the remote AP is authenticated for the VPN and established a IPSec connection, it is assigned a role.

Select the server group from the drop-down menu.Configuring Internal Database for AuthenticationYou can use the controllerвЂ™s internal database as an authentication server. In the Profile list, under VPN Authentication Profile, select Server Group.6. You must install the PEFNG and PEFV license, as described in Chapter 31, вЂњSoftware LicensesвЂќ.5. For Default Role, enter the user role you created previously (for example, RemoteAP).User roles and policies require the PEFNG and PEFV license. In the Profiles list, select the VPN Authentication Profile> default-rap.3. Navigate to the Configuration >Security >Authentication > L3 Authentication page.2.

Configure the VPN server on the controller.4. Configure a public IP address for the controller.2.

Port For Remote Access Mac